I just need you to write one part of the report, which is ( Procedure) ONLY  Note: The rubric is in the file down below  let me know if you need more informations.  Thank you .
I need you to write me lab report, and answer the disctusion questions about ( Isolating of the Active Ingredient in an Analgesic Drus" I attached all the information you may need such as , the procedure, the hazerds, Chemical and physical properties, lab report format, and a picture of the result we got in the lab, I need only 2 pages, one for the lab report, and the other one for the discution questions.  Please check the attachments, and let me know please if you have further questions.  Thank youÂ
  Units are on the scene of a 10,000 square foot warehouse under construction with no interior compartments and a ceiling height of 30 feet. In the center of the structure there is a large pile of debris burning. The molecules within and emanating from the debris fire are at a higher temperature than the surrounding air and products of combustion rise up following the centerline of the plume. As the fire grows the products of combustion form gas layers across the ceiling. As the gases move across the ceiling away from the centerline of the plume they begin to recirculate. Describe which principle applies to this scenario? Describe why the molecules from the debris are located higher than surrounding air. Is there any heat transfer? Why, or why not? In this scenario is the plume considered laminar or turbulent? Why, or why not? Your response must be at least 200 words in length.  Â
Looking for full course help in the subject "Organic Chemistry II - CHM 25600". I have attached syllabus. Please go through it carefully and let me know if you can do it very well assuring high grade.Â
Chemistry Help Needed!!!!! Please read and confirm in your handshake specifically about the project ,deadline and set budget of $25.00 Urgent : need Oct 30 instructions: Water Quality Report Formatting & Content Requirements 100 points in the Test Category General Format and Style Guidelines: The following sections need to be included in your lab report: 1. Introduction 2. Materials and Methods 3. Results 4. Discussion 5. Conclusion 6. Water Quality Inforgraphic 1. Introduction  The introduction defines the subject of the report. It must outline the scientific purpose(s) or objective(s) for the research performed and give the reader sufficient background to understand the rest of the report. § Provide an overall summary and answer the following questions: o What is water testing? o Why is water testing needed? Why is it important to continually test water samples? 2. Material & Methods This section contains the detailed laboratory procedures for readers and the materials that were used in order to conduct the water testing. § The following need to be included: o A list of all the materials used in the lab o The procedures used to complete EACH of the water quality tests o Example: Chlorine Test Material: Chlorine testing strips, color chart, and plastic cups for water samples Chlorine Testing Protocol: Completed on three samples – unfiltered, filtered, and name brand water sample 1. Fill the well plate with your water sample. 2. Immerse one-inch of the chlorine test strip into the water sample. Remove the test strip immediately. 3. Wait one minute for the color to develop, determine the ppm using the color chart. Repeat for the filtered water sample, and the bottled water sample. 3. Results § The results section should summarize the data from the experiments without discussing their implications. The data should be organized into tables and/or figures. Figures and tables should be numbered separately and should be referred to in the text by number.  For the tests completed on the selected samples use the table similar to the one on your data sheet. Test Completed Unfiltered Sample (Sample One – Lindley & Kittridge) Filtered Sample (Lindley & Kittridge) Bottled Brand Water (Aquafina) Chlorine 100 ppm 50 ppm 0 ppm 4. Discussion  This is where you should include the answers to the pre-lab questions and provide a summary of your results. 1. Determine if all of your samples were inside or outside of the optimal range determined in the pre-lab assignment for each of the test conducted. 2. Were there any similarities or trends in your results for the tests you conducted on all of your water samples? (Hint: Think about the geography of your samples) 3. Compare your results to two other groups. Are there any similarities between your results or are your results completely unique? Are there any trends? Be specific when comparing your results. 4. If a sample was outside of the optimal range, what do you think caused the high or low levels? Is there any consequence to these high/low levels? 5. Was there a difference in the filtered water versus unfiltered water samples? If so, does that imply filtering water is an efficient way to clean water? 6. Was there a difference between your water sample and the bottled water sample? If so, what were the differences? Does this mean you will only drink or use bottled water? 7. Based on your results overall, do you think your water samples are safe to consume? Do you trust the quality of your drinking water? Explain why or why not. 5. Conclusion  Summarize the entire lab procedure. Highlight the important steps and findings. How would you improve your experimental outcomes? 6. Water Quality Inforgraphic  You need to design an inforgraphic about water quality in your community. It MUST be designed by hand, no computer generated graphics. NOte: research is required for need information not provide in my notes.
